Ùrachadh mu Dheireadh 14/07/2017
Google pluspinterestShare on Stumble UponShare on RedditFacebookShare on Tumblr
TIOTAL
Iain Friseal, Gobha Inbhir Nis (31 de 39)
EXTERNAL ID
GB1796_SINCLAIR_SILVERSMITH_31
ÀITE
Inbhir Nis
SIORRACHD/PARRAIST
INBHIR NIS: Inbhir Nis 's Am Bànath
LINN
1970an
CRUTHADAIR
John Fraser
NEACH-FIOSRACHAIDH
Taigh-tasgaidh is Gaileiridh Ealan Inbhir Nis
AITHNEACHADH MAOINE
2258
KEYWORDS
seudraidh
seudan
neach-ceàirde
luchd-ciùird
obair meatailt
gobhaichean airgid
claistinneach

Get Adobe Flash player

Dh'ionnsaich Iain Friseal, Gobha Airgid Inbhir Nis, a chiùird anns na 1930an aig Medlock and Craik, seudairean agus luchd-dèanamh uaireadairean aig 6 Sràid na Drochaid, Inbhir Nis. An dèidh làimhe, bha togalaichean aig a' chompanaidh ann an Exchange Place agus Geata na Bànrigh.

Anns an earrann chlaistinn seo bho na 1970an, tha Mgr. Friseal a' cuimhneachadh air na duilgheadasan le teicneòlas solldraigidh. Tha an dealbh seo, a chaidh a thoirt le Taigh-tasgaidh agus Gaileiridh Ealain Inbhir Nis (IMAG), a' sealltainn fear de na h-earrannan aig Iain Friseal - bràiste Clann Fhriseil leis an t-suaicheantas 'Je suis prest' (Tha mi deiseil).

'Well, you smelter your brass filings and stuff like that and silver, you put so much silver, so much brass, until you reckon you had the right colour; too much brass and your solder line came up yellow after a while, after it weathered. If you put it somewhere to stand - well, say it was a quaich and you were putting a foot on it - and you used too much brass in the solder then you'd find a yellow line coming up where the solder was. You could polish it out but it would come back up again, after a time, with the atmosphere.

You'd also got to be careful that your solder was clean because if not you'd get porosity in the solder; you'd get little pockets of air and you would get little pinholes in the solder and it looked dirty, you know, especially if it was a job where you could see a solder line. What you would do is, you would melt it down, then you'd run it into the skillet and let it cool. Then you'd take it out and you'd do exactly the same thing as you did with your wire, only instead of putting it through a drawplate you'd put this through a rollers'

Airson stiùireadh mu bhith a’ cleachdadh ìomhaighean agus susbaint eile, faicibh duilleag ‘Na Cumhaichean air Fad.’
’S e companaidh cuibhrichte fo bharantas clàraichte ann an Alba Àir. SC407011 agus carthannas clàraichte Albannach Àir. SC042593 a th’ ann an High Life na Gàidhealtachd.
Powered by Capture

Iain Friseal, Gobha Inbhir Nis (31 de 39)

INBHIR NIS: Inbhir Nis 's Am Bànath

1970an

seudraidh; seudan; neach-ceàirde; luchd-ciùird; obair meatailt; gobhaichean airgid; claistinneach

Taigh-tasgaidh is Gaileiridh Ealan Inbhir Nis

Bill Sinclair Audio: John Fraser, Silversmith

Dh'ionnsaich Iain Friseal, Gobha Airgid Inbhir Nis, a chiùird anns na 1930an aig Medlock and Craik, seudairean agus luchd-dèanamh uaireadairean aig 6 Sràid na Drochaid, Inbhir Nis. An dèidh làimhe, bha togalaichean aig a' chompanaidh ann an Exchange Place agus Geata na Bànrigh.<br /> <br /> Anns an earrann chlaistinn seo bho na 1970an, tha Mgr. Friseal a' cuimhneachadh air na duilgheadasan le teicneòlas solldraigidh. Tha an dealbh seo, a chaidh a thoirt le Taigh-tasgaidh agus Gaileiridh Ealain Inbhir Nis (IMAG), a' sealltainn fear de na h-earrannan aig Iain Friseal - bràiste Clann Fhriseil leis an t-suaicheantas 'Je suis prest' (Tha mi deiseil).<br /> <br /> 'Well, you smelter your brass filings and stuff like that and silver, you put so much silver, so much brass, until you reckon you had the right colour; too much brass and your solder line came up yellow after a while, after it weathered. If you put it somewhere to stand - well, say it was a quaich and you were putting a foot on it - and you used too much brass in the solder then you'd find a yellow line coming up where the solder was. You could polish it out but it would come back up again, after a time, with the atmosphere. <br /> <br /> You'd also got to be careful that your solder was clean because if not you'd get porosity in the solder; you'd get little pockets of air and you would get little pinholes in the solder and it looked dirty, you know, especially if it was a job where you could see a solder line. What you would do is, you would melt it down, then you'd run it into the skillet and let it cool. Then you'd take it out and you'd do exactly the same thing as you did with your wire, only instead of putting it through a drawplate you'd put this through a rollers'